Stahlwille

238

23 sockets 1/2" with hex No. 52: 10; 11; 12; 13; 14; 15; 16; 17; 18; 19; 20; 21; 22; 23; 24; 25; 26; 27; 28; 30; 32; 34; 36 mm
10 INHEX screwdriver sockets 1/2" No. 54: 4; 5; 6; 7; 8; 10; 12; 14; 17; 19 mm
3 screwdriver bits 1/2" for TORX No. 54 TX: T20; T25; T27 5
screwdriver bits 1/2" for TORX No. 1054 TX: T30; T45; T50; T55; T60
11 sockets with hex 1/4 No. 40: 5; 5.5; 6; 7 ;8; 9 ;10; 11;12; 13; 14 mm
4 screwdriver sockets for hex socket screws 1/4" No. 44 K: 4; 5; 6; 8 mm
6 screwdriver bits for TORX 1/4" No. 44 KTX: T8; T9; T10; T15; T20; T25
1 enlarger No. 410: 1/4" square drive, 1/2" square drive, 28 mm
1 bit holder 1/4" No. 412: L. 25 mm
1 bit connector 1/4" No. 3116: L. 25 mm
1 bit ratchet screwdriver 1/4" No. 4008-1: L. 250 mm
1 telescopic ratchet 1/2" No. 516: L. 410-630 mm
1 QuickRelease cross handle No. 506QR: L. 300 mm
2 QuickRelease extensions 1/2" No. 509QR: L. 130; 255 mm
1 QuickRelease universal joint 1/2" No. 510QR: L. 80 mm
1 QuickRelease fine-tooth ratchet 1/4" No. 415QR N: L. 117 mm
1 QuickRelease plug-in handle 1/4" No. 400QR: L. 150 mm
2 QuickRelease extensions 1/4" No .405QR: L. 54; 150 mm
1 QuickRelease cross handle 1/4" No. 404QR: L. 116 mm
1 QuickRelease universal joint 1/4" No. 407QR: L. 45 mm
1 bit fine-tooth ratchet 1/4" No. 415SGB N: L. 117 mm
1 QuickRelease fine-tooth ratchet 3/8" No. 435QR N: L. 193 mm
1 QuickRelease extensions 3/8" No. 427QR: L. 160 mm
1 enlarger No. 432: 1/2" external square 3/8" internal square
1 reducer No. 431: 1/4" external square 3/8" internal square
1 car test lamp No. 12905: 6-12 and 24V
1 offset screwdriver set No. 10765/9: 1.5; 2; 2.5; 3; 4; 5; 6; 8; 10 mm 9 pcs.
2 offset screwdrivers No. 10765: 12; 14 mm
1 offset screwdriver set TORX No. 10766/8: T9; T10; T15; T20; T25; T27; T30; T40 8 pcs.
1 bit set No. 1206: 1 bit holder | L. 25 mm: SL4;5;6 mm (2x) | PH1;2;3 (3x) | PZ1;2;3 (3x) | T10;15;20;25;27;30;40 (2x) | T BO10;15;20;25;27;30;40 | INHEX 3;4;5 mm | L. 75 mm: SL6 mm | PH2;3 | PZ1;2 | T20;25 | 56 pieces
96830289 TCS 2 2700/23
3 pin punches, octagonal No. 108/150: 4; 6; 8 mm
1 center punch, octagonal No. 105/120: 120 x 12 mm
4 pin punches No. 108: 2; 3; 5; 10 mm
1 locksmith's hammer No. 10961: 500 g
1 flat chisel No. 102/200: W.23 mm L. 200 mm
1 soft-face mallet No. 10959: 50 mm
1 cross chisel No. 103: L. 200 mm
1 locksmith's hammer No. 10961: 1500 g
1 seal scraper No. 12718: L. 265 mm
1 lever No. 11007: L. 400 mm
1 magnetic lifter No. 12600: 3000 g
1 roller tape measure No. 12935/5: L. 5 m
1 flat file No. 12036: l. 250 mm
1 half-round file No. 12030: L. 260 mm
1 round file No. 12025: L. 210 mm
1 precision feeler gauge, 20 sheets No. 11095/20: 0.05; 0.10; 0.15; 0.20; 0.25; 0.30; 0.35; 0.40; 0.45; 0.50; 0.55; 0.60; 0.65; 0.70; 0.75; 0.80; 0.85; 0.90; 0.95; 1.00 mm
1 open-ended wrench No. 4025 12: L. 309 mm
1 wire brush No. 12374: L. 290 mm
96830290 TCS 3 2700/22
22 combination wrenches No. 14: 6; 7; 8; 9; 10; 11; 12; 13; 14; 15; 16; 17; 18; 19; 20; 21; 22; 24; 27; 30; 32; 36 mm
96830291 TCS 4 2700/20
1 caliper No. 12900N: 150 mm/6"
1 PHILLIPS screwdriver No. 4734: PH2
1 slotted screwdriver No. 724: 1.0 x 5.5 x 25 mm
1 cable cutter No. 12320
6 TORX screwdrivers No. 4650: T10; T15; T20; T25; T30; T40
3 PHILLIPS screwdrivers with impact cap DRALL No. 4632SK: PH1; PH2; PH
4 slotted screwdrivers No. 4622SK: 0.8 x 4.0 x 90; 1.0 x 5.5 x 100; 1.2 x 6.5 x 125; 1.2 x 8.0 x 150 mm
1 PHILLIPS screwdriver No. 4632: PH4
1 torch No. 13132: 130 lm
1 wooden folding rule No. 13111: 2 m
96830292 TCS 5 2700/14
2 circlip pliers for inner rings No. 6543: J1; J2; straight; L. 140; 180 mm
2 circlip pliers for inner rings No. 6545: A1; A2 straight; L. 140; 180 mm
2 circlip pliers for inner rings No. 6544: J11; J21; L. 128, 170 mm
2 circlip pliers for outer rings No. 6546: A11; A21; L. 128; 175 mm
1 side cutter No. 6720: L. 160 mm
1 water pump pliers No. 6572: L. 240 mm
1 round nose pliers No. 6529: L. 160 mm
1 combination pliers No. 6700: L. 180 mm
1 wire stripper: max. 4 mm
1 crimping pliers No. 6638: L. 220 mm

Germany

4018754352289

97830265

Assortment

NCNR - Non-Cancellable / Non-Returnable

extra-long wrenches for more leverage in the wrench sizes of up to 36
sockets in the sizes up to 36
metric dimensions
with Tool Control System (TCS)